1 files changed, 87 insertions, 0 deletions
diff --git a/libraries/ESP32Servo/examples/analogWriteExample/analogWriteExample.ino b/libraries/ESP32Servo/examples/analogWriteExample/analogWriteExample.ino
new file mode 100644
index 0000000..9cb9c7e
--- /dev/null
+++ b/libraries/ESP32Servo/examples/analogWriteExample/analogWriteExample.ino
@@ -0,0 +1,87 @@
+/*
+ Mega analogWrite() test
+
+ This sketch fades LEDs up and down one at a time on digital pins 2 through 13.
+ This sketch was written for the Arduino Mega, and will not work on previous boards.
+
+ The circuit:
+ * LEDs attached from pins 2 through 13 to ground. or for ESP32-S2 pins 1-17,19-21,26,33-42
+
+ created 8 Feb 2009
+ by Tom Igoe
+
+ This example code is in the public domain.
+
+ */
+// These constants won't change.  They're used to give names
+// to the pins used:
+#if defined(ARDUINO_ESP32S2_DEV) || defined(ARDUINO_ESP32S3_DEV)
+const int lowestPin = 1;
+const int highestPin = 42;
+#elif defined(ARDUINO_ESP32C3_DEV)
+const int lowestPin = 1;
+const int highestPin = 19;
+#else
+const int lowestPin = 2;
+const int highestPin = 33;
+#endif
+#include <ESP32Servo.h>
+Servo myservo;
+
+void setup() {
+	Serial.begin(115200);
+	// Allow allocation of all timers
+	ESP32PWM::allocateTimer(0);
+	ESP32PWM::allocateTimer(1);
+	ESP32PWM::allocateTimer(2);
+	ESP32PWM::allocateTimer(3);
+}
+
+void loop() {
+	if (!myservo.attached()) {
+		myservo.setPeriodHertz(50); // standard 50 hz servo
+		myservo.attach(33, 1000, 2000); // Attach the servo after it has been detatched
+	}
+	myservo.write(0);
+	// iterate over the pins:
+	for (int thisPin = lowestPin; thisPin <= highestPin; thisPin++) {
+		if (ESP32PWM::hasPwm(thisPin) &&  // Is it possible for this pin to PWM
+				(ESP32PWM::channelsRemaining() > 0 || // New channels availible to allocate
+						pwmFactory(thisPin) != NULL || // already allocated this pin in the factory
+						thisPin == 25 || // one of the  2 DAC outputs, no timer needed
+						thisPin == 26)) { // one of the 2 DAC outputs, no timer needed
+			if (pwmFactory(thisPin) == NULL) { // check if its the first time for the pin or its a DAC
+#if defined(ARDUINO_ESP32S2_DEV)
+				if (thisPin == 17 || // one of the 2 DAC outputs, no timer needed
+						thisPin == 18)
+#elif defined(ARDUINO_ESP32C3_DEV) || defined(ARDUINO_ESP32S3_DEV)
+				if (1 == 0) //  no DAC outputs for these chips
+#else
+				if (thisPin == 25 || // one of the 2 DAC outputs, no timer needed
+						thisPin == 26)
+#endif
+				{
+					Serial.println("DAC to pin " + String(thisPin));
+				} else
+					Serial.println("Writing to pin " + String(thisPin));
+				pinMode(thisPin, OUTPUT);
+			}
+			// fade the LED on thisPin from off to brightest:
+			for (int brightness = 0; brightness < 255; brightness++) {
+				analogWrite(thisPin, brightness);
+				delay(1);
+				myservo.write(brightness);
+			}
+			// fade the LED on thisPin from brithstest to off:
+			for (int brightness = 255; brightness >= 0; brightness--) {
+				analogWrite(thisPin, brightness);
+				myservo.write(brightness);
+				delay(1);
+			}
+
+		}
+	}
+	myservo.detach(); // Turn the servo off for a while
+	delay(2000);
+
+}